C18
Cat® C18 ACERT Propulsion Engine (Tier 3)
C18
The Cat® C18 commercial propulsion engine is built to deliver reliable, high-output power for workboats operating in demanding marine environments. Its inline 6-cylinder, four-stroke diesel design provides the durability and performance needed for long hours, heavy-duty duty cycles and consistent propulsion. Supported by the global Cat dealer network, the C18 helps keep vessels productive, serviceable and ready for the next job.
- Specifications
- Standard / Optional Features
- Long Name -Cat® C18 ACERT Propulsion Engine (Tier 3)
- Name -C18
- Brand -Caterpillar
- Status -Current
- Power Range - 454 - 1136 bhp (339 - 847 bkW)
- Application - Workboat
- Speed Range - 1800 - 2100 rpm
- Emissions - U.S. EPA Tier 3 Commercial, IMO II, EU Stage V, China II
- Aspiration - Turbocharged - Aftercooled
- Bore - 5.7 in / 145 mm
- Stroke - 7.2 in / 183 mm
- Displacement - 1106 in³ / 18.1 l
- Rotation from Flywheel End - Counterclockwise
- Oil Change Interval - 250 / 500
- Refill Capacity - 49 / 68 l
- Configuration - In-line 6, 4-Stroke-Cycle Diesel
- Cooling - Heat Exchanger or Keel Cooled
- Governor - Electronic
- Flywheel Housing - SAE No. 0 (136 teeth) or SAE No. 1 (113 teeth)
- Minimum Dry Weight - 4000 lb / 1814 kg
- Minimum Length - 73 in / 1854 mm
- Minimum Height - 47.2 in / 1198 mm
- Maximum Height - 51.2 in / 1300 mm
- Minimum Width - 44.6 in / 1134 mm
- Maximum Width - 47.4 in / 1204 mm
Standard Equipment
- air inlet system
- Separate circuit after-cooled (SCAC)
- Open Crankcase Ventilation (OCV) system
- Turbocharger, jacket water cooled
- Turbocharger inlet, 152 mm (6 in) OD straight connection
- Air Start Accessories
- cooling system
- Separate Circuit After-Cooling (SCAC) for both HEX and Keel cooled engines
- Engine JW and SCAC Shell & Tube Heat Exchangers for HEX cooled engines
- SCAC pump, gear driven, for HEX cooled engines only
- Jacket water pump, gear driven
- Sea water pump, bronze impeller, gear driven
- SCAC and JW shunt tanks for maintaining proper pump inlet pressures
- exhaust system
- Water-cooled exhaust manifold & turbocharger
- 152 mm (6 in) round flanged outlet
- flywheels & flywheel housings
- SAE No. 0, Flywheel SAE. 18, 136 teeth
- SAE No. 1, Flywheel: 14 inch, 113 teeth
- fuel system
- Front service simplex fuel system
- Fuel transfer pump, gear driven
- Manual fuel priming pump
- Hybrid fuel line design
- lube system
- Front service simplex oil system
- Center sump oil pan: Deep 500 hour oil change interval, Shallow 250 hour oil change interval
- Front and top service oil filler locations
- Front service dipstick
- Oil pump, gear driven
- mounting system
- Front support - adjustable
- power take-offs
- Poly-V groove for alternator drive
- NOTE: There are no standard power take-offs available
- general
- Front damper guard
- Front service engine
- Common electrical bonding point
- Engine does not ship with zinc components
- control system
- Programmable low idle
- WOSR (Wide Operating Speed Range) available for EPA Tier 3 - B and C Ratings
- Adjustable High Idle (TEL) - EPA Tier 3 WOSR Ratings Only
- Electronic diagnostics and fault logging
- Engine and transmission monitoring (speed, temperature, pressure)
- Electronic fuel/air ratio control
- Engine Protection Mode for extended ambient conditions - EPA Tier 3 Ratings Only
- 70-pin customer connector
- Three types of throttle inputs (primary/ secondary PWM, 0-5V, 4-20mA +/-
Optional Equipment
- exhaust system
- Dry Elbows
- Water-Cooled Elbows
- Flexible Fitting
- Outlet Flange
- Muffler
- Muffler Spark Arresting
- air inlet system
- Air Inlet Adapter
- charging system
- Battery Chargers
- Charging Alternators
- Alternator Mounting Group
- Ammeter
- control system
- MECP-I
- CAT Alarm and Protection
- cooling system
- Aux expansion tank flange kit
- Exhaust Temp Sensor
- Heat Exchanger Pressure Sensor
- fuel system
- Duplex Fuel Filters
- Flexible Fuel Lines
- Fuel Cooler
- Fuel/Water Separator
- instrumentation
- Instrument Panels
- OEM Wiring Harness
- Engine to Engine Harness
- Transmission Sensors
- Oil Level Sensor
- instrumentation
- Digital Tachometer
- lube system
- Duplex Oil Filters
- Transmission Oil Cooler
- Sump Pump
- mounting system
- Vibration Isolators
- Front Support
- Rear Support
- power take-offs
- NOTE: PTO options require torsional vibrations analysis
- Crankshaft Pulleys
- Front Stub Shaft
- Hydraulic Pump Drive Adapter
- Front Enclosed Clutch
- protection system
- Marine Classification Society and SOLAS
- starting system
- Electric Starting Motors - Single 24 Volt
- Starting Aids - JW Heater 120 / 240V
- Single Electric 24V Starter
- Battery Sets - 24 Volt - Dry
- Single Air Starting Motor
- packing
- Engine Protective Cover
- Storage Preservation
- Export Packing